Fetter Pro - Chain & Rope Wrap for Blender

GreyFox Studio in Presets


Wrap real chains and ropes around any mesh in Blender, in one click: chained coffins, bound crates, roped barrels, sealed chests, shackled statues. Hang them between two posts, lay them along a curve, or coil a rope on a nail.

NEW IN 1.10.0 - PADLOCKS AND A HOOK MODELLED BY HAND

A Medieval padlock (a shield-shaped forged lock, keyhole on the front), a Modern padlock (a block lock, key at the bottom) and a forged Eye Hook on a riveted swivel eye. Each one is under 1,500 triangles, unwrapped with no overlap, with its own sharp edges. The S-Hook stays.

NEW IN 1.9.0 - ROPE COILS AND A REAL LOW POLY ROPE

Coiled Rope and Coiled Chain: a coil on its own, hung on a peg, dropped on the floor or laid flat. Plain Tube turns a rope into a simple tube, a real low poly, and Make Bake Pair gives a rope a plain tube as its low copy.

Pick a few edges of your prop, press Wrap with Chain or Wrap with Rope, then dial in the turns, the spacing, the tilt and the link size live. Every link is a real interlocking link that never cuts into the prop or into its neighbours, and every closed ring closes seamlessly. Lock it shut with a padlock, or end a chain with a forged hook.

FEATURES

- Draw Wrap: no Edit Mode and no edge to select. Drag a line across the object and the chain or rope goes around it there, on any mesh. Height and Lean adjust it afterwards

- Hang between two objects: select two posts, press Hang Chain or Hang Rope, and it hangs between them with a Sag setting. Move either post and it follows

- Chain & Rope on Curve: click a curve with the pipette and a chain or rope lies along it, every spline of it (Bezier, poly or NURBS). Edit the curve and it follows

- Coiled Rope & Chain: a coil of rope or chain on its own, at the 3D cursor: hung on a peg, dropped on the floor or laid flat. Snap its origin onto a nail; Gather at Peg keeps the loops together on a short hook. Loops, Size, Loop Width, Messiness and Ends shape it

- Four ways to pick: separate edges along the object (the 4 long corner edges of a crate, a coffin or a chest), its faces, one edge loop around it, or an open edge path to follow. A line in Edit Mode tells you what your selection will give

- One wrap per part: select the faces of several posts and wrap each one on its own

- Rings or one continuous spiral, any number of turns, spread over the selection, centered, forward or backward. Turns never come closer than the chain or rope is wide

- Crossed patterns: tilt the rings and alternate the tilt for X crossings, or randomize tilt and offset with a seed

- Real interlocking links: each link alternates 90 degrees with its neighbour, closed rings close seamlessly, links never intersect, even at sharp corners or crossed at 45 degrees

- Five link shapes: oval, square, round, stud (a bar across each link, as on an anchor chain) and twisted

- Tight wrap: flat on the faces, a link straddling each corner, never inside the mesh

- Tighten: one slider closes the chain or rope in until it rests on the surface, with no gap and nothing floating, or pushes it away

- Slack: let the rings hang loose and sag under the beam or the log they go round

- Follow Shape: the wrap hugs the part of the mesh it goes around. A chain on a shaft stays on the shaft, even between a wide base and a wide head

- Tie Another Object: wrap a tree, click the skeleton with the pipette, and the rope goes around both and ties them together. The meshes parented to the object are tied too

- Crossings go over: later wraps lift over earlier ones on the same object

- Twisted rope: 1 to 8 strands, adjustable twist length, ends cut plain, frayed, whipped or tied in a stopper knot

- Real low poly rope: Plain Tube turns the rope into a plain tube that follows it, a fraction of the triangles (61,000 down to 4,200 on a coil)

- Padlocks, modelled by hand: Medieval (shield-shaped, keyhole on the front) or Modern (block, key at the bottom), threaded through an upright link and resting over the chain; around a post they hang straight down. On the first, middle or last ring, every other ring or all of them

- Hooks: a forged eye hook on a riveted swivel eye, modelled by hand, or an S-hook, on the free ends of a spiral, an open chain, a curve or a hanging chain

- Presets: Prison Chain, Anchor Chain, Fine Chain, Ship Rope, Rope Coil and Game Low Poly in one click

- Live and non-destructive: every setting rebuilds the wrap at once, Undo brings it back with its settings, the wrap stays parented to its prop and follows its edits, modifiers and pose. Finalize turns it into a plain mesh

- Game ready: one mesh, every link its own island, 36 to 4096 triangles per link, UVs shared (tiling materials) or unique per link (Substance 3D Painter). Padlocks and hooks under 1,500 triangles each, unwrapped with no overlap, sharp edges kept

- LODs and bake pair: Make LODs and Make Bake Pair create LOD1, LOD2, low and high copies in one click. A rope's low copy is a plain tube, its high copy the twisted rope

- Color per Link: a color attribute to vary rust and wear link by link in Substance 3D Painter or Unreal Engine

- Material slots Fetter_Chain_Iron, Fetter_Rope and Fetter_Lock_Iron; your own materials stay in them at every rebuild

- Its own panel, in the order of the work, with an info popup and a small diagram on every control. It tells you in orange why a wrap cannot be built

WHAT YOU GET

- The Blender add-on (fetter_pro-1.10.0)

- The full user guide (HTML)

REQUIREMENTS

- Blender 4.2 or newer (tested on Blender 5.1.2)

- Windows, macOS, Linux

NOTES

- A turn is pulled tight round the part of the prop under it, like a real chain: it bridges hollows instead of following the surface into them.

- Only the wrapped object (and the object tied to it) is used as the collision shape: join separate parts first, or wrap each part.

- Slack, hanging chains and coils are shaped, not simulated: they do not rest on the objects around them.

- Hooks need free ends: use a spiral, an open path, a curve or a hanging chain.

- The meshes you make with Fetter Pro are yours, for personal and commercial projects.

Made by GreyFox Studio - https://unreal-engine.greyfoxstudio.ca/products/fetter


$19.95

Have questions about this product?
Login to message

Details
Blender Extension Compatible Yes
Published 1 day ago
Blender Version 4.2 - 5.1
Extension Type Add-on
Render Engine Used Cycles, Eevee
License GPL